Castors for Scaffolding, Platforms and Mobile Work Stands

Castors for Scaffolding, Platforms and Mobile Work Stands
Castors on a trolley and castors on a work platform do the same basic job, but the consequences of getting it wrong are very different. A trolley that creeps is annoying. A platform with someone standing on it that moves is a fall risk.
That changes the specification. Stability, braking and load rating matter more than ease of movement.
What's different about work platforms
Three things set platform castors apart from general purpose castors:
People are on top. The load isn't static, and users shift weight, reach and climb.
The structure is tall relative to its base. Any movement or soft wheel flex is amplified at height.
The castors are used on job sites. Floors are often uneven, dusty or wet.
Start with what the equipment maker specifies
For a prefabricated mobile scaffold tower or a manufactured access platform, the castors are part of the tested design. Use the type, size and rating the manufacturer specifies, and don't swap them for a similar-looking castor.
If you're replacing a worn castor on one of these units, match the manufacturer's part. If the original isn't available, check with the supplier before substituting. In New Zealand, scaffolding work is covered by WorkSafe NZ guidance, and mobile scaffolds are commonly built to AS/NZS 1576. Confirm the current requirements for your equipment and job.
Features that matter
1. Total lock brakes
A total lock castor stops both the wheel and the swivel, so the base can't roll or pivot. Top lock (wheel-only) brakes allow the castor to swivel and are less suited to platforms. Every castor on a work platform should be braked, not just two.
2. Load rating with margin
Work out the total mass: the structure, the platform, people, tools and materials. Divide by three for a four-castor base, then add a safety margin. The load calculator helps with the numbers.
3. Wheel diameter
Larger wheels roll over joints, cables and debris more easily and reduce the risk of the base stopping suddenly. Typical work platforms use around 125 mm to 200 mm diameter, depending on load and floor.
4. Solid wheels, not soft ones
Soft rubber and pneumatic tyres flex under load, which makes a tall platform feel unstable. Solid polyurethane or nylon wheels are firmer. Pneumatic wheels are fine for moving a platform over rough ground, but they aren't ideal for working on.
5. Floor protection
On finished floors, non-marking wheels prevent scuff marks. On rough or outdoor ground, a harder wheel with a wider tread gives better support.
Matching castors to equipment type
Equipment | What to prioritise |
Mobile scaffold tower | Manufacturer-specified castors, total lock brakes on all four |
Mobile work platform or access stand | Total lock, solid wheels, adequate wheel diameter |
Workshop work stand or low platform | Load rating, brakes, floor protection |
Mobile staging or display platform | Non-marking wheels, lockable, smooth rolling |
Heavy equipment stand | High load rating, cast iron or steel wheels, heavy duty castors |
Safe use on site
Good castors don't make a platform safe on their own. Basic habits matter just as much:
Lock every castor before anyone climbs on.
Don't move the platform with people or loose materials on it, unless the manufacturer's instructions permit it.
Keep it on firm, level ground. Castors aren't a substitute for levelling.
Check castors, brakes and fixings before each use, and take damaged equipment out of service.
Pro tip: brakes wear. Put a quick brake test in the pre-use check: push the platform with all castors locked. If it moves, the brakes need attention.
Custom bases and mounting
When a platform needs a bespoke base, with reinforced mounting plates, outriggers or a particular footprint, a well-built frame matters as much as the castors. Vartec's custom fabrication team can build bases to suit, and the castor by application page lists the options by use.
Need a recommendation? Call 09 444 1335 or email sales@vartecindustrial.co.nz with the equipment type, total load and floor surface.
FAQ
What castors are used on scaffolding towers?
Mobile scaffold towers use heavy duty castors with total lock brakes, sized and rated by the tower manufacturer. Use the castors specified for your tower, and don't substitute generic ones.
Do work platform castors need brakes?
Yes. A platform with people on it must not move, so every castor should have a brake. Total lock brakes, which stop both the wheel and the swivel, are the safer choice.
What size castor is best for a mobile work platform?
It depends on the load and the floor, but larger wheels roll over uneven surfaces more easily and are safer. Many work platforms use roughly 125 mm to 200 mm wheels.
Can I use pneumatic castors on a work platform?
They're useful for moving a platform over rough ground, but their flex can make a tall platform feel unstable when someone is working on it. Solid wheels are the better choice for use.
How do I work out the load rating I need?
Add the structure, platform, people, tools and materials. Divide by three for a four-castor platform, then add a safety margin. Our load calculator can help.




Comments